DELEIKA 2017 Maserati LOGO Car door LED logo projector Light ghost shadow light For Quattroporte Ghibli GranTurismo GranCabrio Levante (Quattroporte, LOGO:2)

First of all, this part seems better quality than the OEM.I read the reviews on this which included installation pointers and thought I was well prepared for installation. I wasn't.Step 1: With a small regular screwdriver, pry the old lens out. Be prepared, I broke the retaining bracket off both lenses.Step 2: Use an awl or something pointed to depress the connector retainer and pull the connectors gently apart.Step 3: Push the male ends of the whip that comes with the light into the cars connector. This is actually the hard part. See the picture. Slide the rubber insulation up to cover the leads.Step 4: Insert the other end of the connector into the light.Step 5: Check the orientation of the logo and install by sliding the wire side in first, gently pushing toward the wired side, push the other side up.

2014 Maserati Ghibli S Q4: Wished it would have come with directions as it is not direct plug and play but came with an adapter harness, however, once my old eyes figured out which way to slide the bare ends of the adapter harness (there are 2 independent leads) into the car door harness plug (very tiny & hard to see) it was a no-brainer and a very easy install. They look brilliant! Tip: look at the male ends inside the fixture you remove from the door to see how the new wiring harness plugs orientation should be when inserting into the door wiring harness plug and it becomes a very easy, 2 minute install. Also, make sure to slide the supplied sleeves over each lead to protect from shorting as they are very close together.

These are one of the "coolest" easy upgrades you can do your car. It's a wonder why it's not a standard yet, given the free advertising. My 2015 Genesis G80 has been doing this since day 1. Anyhow, I clearly loved the effect and went for it. Installation was simple despite the lack of instructions. You simply use a flat head screwdriver to remove your existing one, disconnect it, and then link the two wires and reinstall and you're good to go. One thing to keep in mind this is a 2 pack, so if you want to cover all 4-doors you'll need to purchase 2x of these.

Received 2 lights today and installed them in the front doors of my 2018 Ghibli. The DELEIKA light fixtures are sligthly larger than the OEM fixtures that you remove. At first seem like they will not fit but they do pop into place if you push them in firmly. The new lights are not “plug in” ready, i.e., they do not plug in directly to the plug connection of the OEM light you take out, but came with wire taps that plug into the wire harness of the old lights and then into the new light. Pretty easy and took no more than 5 minutes for both lights. Picture attached. They are very bright and pretty cool. I cannot talk about how long they last but given they are LED’s I’d expect long life

Must have for sure. Great quality and very very easy to install. It takes less than 10 seconds. Seller is also a great source

I purchase these for my Maserati Granturismo sport because they were advertised as plug-and-play no wiring required. That was not the case I had to get them expertly installed which cost around $60 bring the total cost over a hundred. other brands are easily plug & go.. do-it-yourself. And they didn't fit snugly into my vehicle like advertised. the installer had to make adjustments for them to fit

The item does not fit on the Granturismo. The light is too small and will not attach properly onto the door. Need to do some modifications/use glue or tape to hold the light fixture in place.

I purchased these for my 2011 GranTurismo Cabrio. They fit the car with no modifications to the car wiring or bottom cut out in the door. 15 minute install with no tools other than a small flat blade screwdriver to pry out existing light. The lights come with their own wiring with plug in. There are things you need to pay attention to during install.1) Removing existing plastic housing from bottom of door. Carefully pull back plastic clip using small flat blade screwdriver.2) Disconnect plug wiring from plastic housing. Insert each pin of the supplied wiring harness into the female ends of the plug that is attached to your door wiring harness. Make sure red goes into red side of female connector and black into black side of female connector. Then slide the protective clear sleeve over the rest of the exposed metal ends.3) Take other side of wiring harness with connector and insert it into the new light. **Pay attention to verify that you have the left side for the left door (drivers side) and right side for the right door (passenger side) They are marked.4) Verify the pins inside the new clear light housing have indeed slid into the correct position of the connector receptacle as the could miss and actually spread the pins apart instead of making contact.5) Slide all wiring back up into the door and insert the housing into the slot. It may not fit snuggly as the original but mine was still enough to hold it in place. You may need some double sided sticky tape to hold it firmly.6) Close the door and the open to verify its working properly.

good product, worked well for me