Pro Marine Supplies Crystal Clear Bar Table Top Epoxy Resin Coating for Wood Tabletop - 1 Gallon Kit

I used this epoxy to cover an 11sq.ft. table filled with approx. 1300 bottle caps. I thoroughly read all instructions, and mixed what I thought was the right amount of product for a seal coat. Turns out I was completely wrong, and once I starting pouring and realized I didn't have enough, I panicked and started eyeballing multiple other batches and mixing rather vigorously and probably not for long enough. I thought for sure I ruined my project. Well, after my horrendous attempt at following the directions meticulously, turns out that my project cured as hard as a rock within the 10 hrs.Next mistake i made: I only bought one of these kits when I needed 2 to completely cover all the bottle caps. I quickly ordered another kit and It was at my door in 2 days (clearly outside of the 10 hour re-coating window). Because at this point I am just throwing caution to wind, I mix both jugs together in their entirety (for like 20 min though) and did one enormous coat. I did not sand or prep the table in any way between the first batch and the second batch 2 days later.Well, my project turned out perfectly smooth, crystal clear, rock hard, with very very few bubbles that no one would ever notice unless they were staring at my table with their face less and 6 inches away from it looking for specifically for flaws. I don't anticipate my guests doing this.I am thrilled with the results, and I don't want all these reviews about "following the directions to a T" scare any beginner epoxiers away.Note: I am NOT recommending you proceed with this product in the same manner I did. Definitely try to follow the directions. I just wanted to provide some insight on my experience that was apparently drastically different than some other reviewers.

We've been using this epoxy resin to finish an outdoor coffee table and and a bathroom countertop. It takes a little bit to get the techniques down, but the results are amazing. I think it is the cheapest, easiest way to update countertops. We are going to do our biggest project next and do our kitchen counters. We purchased the 2-gallon kit for that. We used Stone Coat Countertops to learn how to do the counters. This epoxy is easy to mix and has a relatively long working time. Definitely do your homework before you start your project, because once you start, you're committed to the process. I would suggest doing some smaller projects, like a coffee table before working on a big, permanent project.If you found this review helpful, please click on the 'yes' below.

This stuff worked amazing on my very first try. I made a large resin table with embedded license plates and it came out spectacular. READ ALL THE INSTRUCTIONS BEFORE YOU START AS PAINFUL AS THAT MAY BE. THEY REALLY HELPED ME. A couple tips:1) My project required 4 gallons of product. (3ft by 3ft, 1/2 inch deep - with plates) I accomplished this in (2) pours, each 4 hours apart2) I mixed 2 gallons for 7 minutes each time and it came out awesome - don't scrape your mixing sticks when you get to the pouring part because you only want thoroughly mixed product to be poured - not remnants of either part alone that you may get if you scrape3) POUR PART B IN YOUR MIXING BUCKET BEFORE PART A - MIXING WILL BE SO MUCH EASIER

Level your project on a waist-high surface with blocks under, project should not have and holes or gaps. Mix epoxy at a 1/1 ratio, be extra carefull about this. Stir well for 5-10 min, but dont whip, should turn completely clear like water, bubbles are okay. Pour evenly back and forth. Spread entire top quickly with a notched plastic 4" putty spreader, I made my own triangle notches with scissors. Use the container to catch edge drips. Use a nylon brush for the sides. Light a butane torch and move quickly popping the bubbles, not too close. Repeat this every 10 mins for 1 hour. Scrape epoxy from under edges and apply to any areas that may lose some from leveling. Let dry 12-16 hours. It will be crystal clear like water and hard like nail polish. Looks professional. Remember, MIX as PERFECT as you can 1/1, and stir very very well. My only complaint is that its over priced and not a lot of room for error.

Provided a beautiful finish on our bar. Take note to ALWAYS brush on a THIN for the first coat to seal the wood. The instructions arent too clear on this until you get to the FAQ. I had to sand down an area that bubbled up due to pouring too thick of a first coat.

This product was easy to use and had very little odor. I used it as a final finish on my art projects and also with my resin art. Clear and hard finish.

I bought this epoxy to finish a bar top I plan to use on a covered, outside bar once Spring arrives. This was my first experience with an epoxy such as this and some of the previous reviews had me a little nervous, but I didn't run into any issues and I'm happy with the results. I poured the resin in a basement that was ~60 degrees and had no problems with applying it or with it curing. If you are working in a cool environment I'd recommend warming up the bottles of epoxy a little before mixing as it makes the mixing process much easier. Overall I am very happy with this product and will definitely be using it again in the future.

This did a great job on our countertops. Mixed it for five minutes for 32oz batch. No soft spots or stickiness. I used a high density foam roller to apply this to a painted countertop and a roller is the way to go rather than using a foam brush. You should let it sit about 16 hours before you touch it. Give it 24 hours before you sit any thing on the epoxy and say 36 hours before you put any thing heavy on it.