Ultradecals American USA Flag DJI Mavic Pro Skin Wrap Decal Sticker Battery Body

I normally don't skin anything, but my Mavic Pro was so ugly, I thought I'd give it a try. I was actually surprised at how well all the pieces fit, with the exception of the front legs, and I could not figure out how they were supposed to go on, so I'm pretty sure I did them wrong. Too bad there's zero instructions, even on their website.A few tips:- Go slow. It took me probably two hours total.- Use alcohol and wipe it down completely, to remove grease and dirt. 99% is best, but 70% will still work. It just takes longer to dry.- If you don't care about the original surface of the Mavic, then take 100-120 grit sandpaper, steel wool, or emery cloth to all the areas you will place the decals. It roughs the surface up, and gives the adhesive something to really bond to. You will obviously ruin the original finish if you do this.- Don't worry about taking a razor to the edges, until after you run the heat gun over it.- Wear gloves, so you don't get greasy fingerprints on the nice clean surface.- Spray a small amount of Windex on the decal. It lets you reposition and slide it into place. It dries slow enough that you have quite a bit of time to work with the decal.- Don't worry about the edges, or small pieces not sticking, the heat gun will take care of that.- When you are satisfied with the placement of the decal, go over it for a little bit with a hot air gun. I had mine set at 160 C. This will get the adhesive nice and gooey, and help create a strong bond. It will also kinda shrink-wrap the decal to fit the shape of the part better. While it's still warm, press down on every area of the decal, and run your finger along the edges, to get them to stick, or round them around the edges of the part.- Leave your drone alone for 24 hours to let the adhesive achieve a maximum bond to the plastic.- Enjoy

Love the look. The wrap is of good quality. I took my time applying each piece. Using an exacto knife to make a micro trim here and there. Also I recommend the use of a heat gun. This helped for flawless adhesion and kept those pesky wrinkels completely away. I also appreciate that the kit came with 2 extra wraps for a total of 3 batteries! The only downside was figuring out where each wrap went as the kit came with no instruction to placement. I recommend watching a few YouTube videos as I did, making the whole process easier. To sum it all up, my mavic 2 pro has a new skin, and I absolutely love the look. Remember, watch a few YT vids, have an exacto knife on hand, use a heat gun, and take your time! You'll wind up with a look you'll love and a " wow " from all your friends!

This is a great product if you want your mavic to stand out from the crowd. It is very complete. High quality vinyl has a glossy finish. It is not a stick and go application. It will take some time to apply. Some of the decals have to be stretched and manipulated to fit the curves of the mavic properly. They will require some trimming after installation to get a professional look. I used alcohol wipes to clean all surfaces first. I also used an exacto knife to do some final fitting and trimming. It looks great when finished. Just remember it's a thousand dollar drone. Be patient and careful and it will pay off. I have tried a few wraps and this one is by far the best.

Very disappointed in this. It wasn't cut correctly to match up the holes and there are zero instructions on any website, YouTube or with the package. I have a very nice set of decals stuck on paper and not on my drone because they simply do not align without covering up air or connection ports. I rarely write negative reviews, yet wish I had read the reviews here before purchasing.This could be a very good product if there were labels and any kind of instructions. Disappointed!

Once applied, it looks nice, but no instructions at all so trying to figure out where each piece went was a pain.

The cuts did not match the drone as precisely as other decal manufacturers, leaving some small gaps and bubbles that had to be addressed with tools. That said, the issues were small enough that most people wouldn't notice them.

I wouldn’t even give it 1 star. I got this for Christmas and I’ve gone past my window of return. When applying decals it was not cut very well and was hard to remove. Once removed I applied to the controller. Holes didn’t line up and vinyl was too big for controller. Oh well I can live without the decal on the controller because the drone is gonna look awesome! WRONG!!!! Decals were too big overlapping other decals and were very hard to remove. Complete disappointment. I even ordered 2 of these so I had a backup incase of a crash. Complete waste of money!

Love the Skins, but no customer support, it only comes with TWO battery skins. I NEED FOUR !tried to contact them but no answer. good luck !Skin it self is good to work with. 5 Stars for that !