BachmannTrains - Freightmaster Ready To Run 60 Piece Electric Train Set - N Scale,Silver , 0.5 Liters

Outstanding buy. DCC is the way to go and this is an awesome set.

The media could not be loaded. After buying this set, I bought an additional identical locomotive, cars, track and accessories to expand my railroad. It is now a realistic 27 car train with two back to back locos powering it. I endeavored to buy cars that were unique and highly detailed. I tried a figure eight pier system but had too many problems with uncoupled cars. N scale railroading is a little finicky in that some cars are hard to couple, and some cars uncouple for no reason. When this happens, I just turn the car around and try again. If that doesn't fix it, then I move the car to another part of the train. Eventually I found a combination that meant for a stable train. Now all is good as you can see from the video of my train set up on my desk in my office. You will have to clean the loco wheels and track periodically. The alternative is to apply NO-OX-ID A-SPECIAL to your tracks following the instructions that follow. After which you'll never have to clean your tracks again. You can buy this on eBay or Amazon for a few bucks. Here are the instructions:All contaminants such as plaster, glue, or oil, should be removed prior to No-Ox application. The steps below are all VERY important and none should be skipped.1. Clean the loco wheels with alcohol on a rag, and clean the rolling stock wheels with blue painters tape on the track, sticky side up.2. Use a mild abrasive such as fine sandpaper to remove all oxidation. I used fine sandpaper starting with 1000 grit, then 1500 grit and finishing with 2000 grit. Whenever the rails are treated, I treated the top as well as the inside of the top of the rails where the wheels also make contact. I also burnished the inside top of the rails with a spoon.3. Wipe all rails with a lint-free rag and alcohol to remove any dirt and fine particles.4. Vacuum all rails to ensure cleanliness.5. Put very thin smears on your finger and rub it on your rails, both the top of the rails and the top inside of the rails. The total amount of NO-OX-ID “A SPECIAL” that should be applied to 500’ of N scale track is about ¼ teaspoon. If you can SEE No-Ox on rails, you are putting TOO MUCH on! DO NOT APPLY MORE!6. Run all your locomotives, EXCEPT ONES WITH TRACTION TIRES, (no rolling stock yet) over all of your track for at least 2 hours. You may notice some wheel slippage and skipping, (DO NOT PANIC) this ensures that all wheels get treated with No-Ox and that No-Ox is applied evenly to all rail surfaces.7. Remove all locomotives from track and wipe all rails with a clean rag to remove any excess product. Rag will be black. Don’t scrub, just rub.8. Wait 24 hours to allow for bonding to the track.9. Wipe rails again. Rag will also be black, but less so than in step 6.10. For locos with traction tires, turn them upside down, connect track power so that wheels turn. Put a small dab of No-Ox on a Q-tip and apply to all wheels that DON’T have traction tires. While wheels are still turning, use a clean Q-tip to remove any excess No-Ox (I didn't do this step since I don't have locos with traction tires).11. Run trains and forget about cleaning your track except for occasional light vacuuming.

The media could not be loaded. Cars stay connected, system is quite and runs well.

The media could not be loaded. My wife wanted a model train for Christmas so she got this set. It’s lots of fun and easy to setup.

Ok folks there are lots of mixed reviews but here is the skinny on mine. I ordered this to run thru my Christmas villages. The scale in relation to the village is too small, HO would be more appropriate; however, the counter space that I set up on is only 25" deep. When I set the track up the caboose kept falling off. It did not matter super slow or fast it would not go one lap around the track before it fell off. I decided to run my finger along the track connections and found several that we misaligned. I corrected these and low and behold, fast, slow, forward, backward the dang thing stays on the track every single time. My only complaint is the engine is a bit noisy at higher speeds but I guess that is to be expected. I love my train. Yes - I would buy this again!

This was hard for a your boy to assemble and probably not going to get much use. The tracks assembled unevenly and the trains hoped a bit causing derailments. Pretty much wish I never purchased this train set. My boy was 11 but assembly was difficult for me as well. The tracks would not join in a way where the trains would not hop and derail. I have experience with train sets and this was my son’s first set.

Lo siento un poco lento a su máxima velocidad, sin embargo es un muy buen producto, me encantó

This train set was a Christmas present for my son. Upon opening the box and setting up the train, several things happened. First one train car that carries the freight boxes fell apart and a set of it's wheels would not stay in place. Then another train car, the box car, wouldn't couple up to any of the other train cars as it's coupler was slightly higher than the others. Aside from these issues, we decided to place the engine on the track and see if it worked. After making sure all tracks were connected properly and plugging in the electrical supply, the engine did not budge. A complete waste of money and a big disappointment for my son who thought this set was very cool. We have Lionel o gauge trains and after this purchase I will never buy from bachmann again. Save your money and look elsewhere.